How to unbrick hard bricked Yu Yureka Plus

Hi, This is an Fully worked and Approved unbrick hard bricked Yu Yureka Plus guide. I have personally unbrick hard bricked Yu Yureka plus using this guide. when i bricked my yureka plus,then I try so many methods and read lot of guides but I found many mistake them, so I try to make a prefect guide for it and try to provide all required tools and drivers in this guide for unbrick hard bricked Yu Yureka Plus.

If your phone in under warranty then you should call customer care and replace or repair your phone.  Here we have Two Methods to unbrick hard bricked Yu Yureka Plus. Method 1: By QDLoader 9008 mode (if your device show in QDLoader 9008 mode) and Method 2: By short main board (if your device don’t show in QDLoader 9008 mode).

Preparation of flash or update:

1. Your phone battery should charge 80% minimum.
2. Read all steps then do it careful.
3. Make sure proper power backup of your PC.
4. You need a memory card(16 or 32GB) with card reader

Must Read: Secrets Tips and Tricks of Lollipop Micromax Yureka Plus

Download ROM and Tools of Yu Yureka Plus :

FILE NAMEDOWNLOAD LINK
Yu Yureka Plus Stock Rom Fastboot imageDownload
Yu Yureka Plus fastboot flashing packageDownload
Yu Yureka Plus eMMC ImageDownload
Yu Yureka Plus eMMC Image writer toolDownload
Yu Yureka Plus USB DriverDownload

Method 1: Follow steps to unbrick hard bricked Yu Yureka Plus:

Step 1: Download and Extract Stock ROM and fast-boot flashing package of Yu Yureka Plus in a folder, where you want. And Download and Extract Yu Yureka Plus eMMC Image and eMMC Image writer tool.

Step 2: Now insert your memory card in card reader and Quick format with Fat32. Then remove your card and wait at least 1 minute. And insert your formatted memory card in card reader, then insert card reader in your PC USB port.

Step 3: Now install eMMC Image writer tool on your PC and write Yu Yureka Plus eMMC Image to your memory card. After successful write Yu Yureka Plus eMMC Image to your memory card, then remove your Memory card from card reader and wait 2 minutes. Now remove your All sim cards, then insert your Memory Card (eMMC Image) in your Yu Yureka Plus.

Step 4: Now open Stock ROM and fast-boot flashing package folder of Yu Yureka Plus and click on “flash-all.bat” to run it. Now you can see command window, in this command window you will see a message “< waiting for device >”.

Command windows for fast boot

Step 5: Now connect your Yu Yureka Plus in fast-boot mode (Press and hold Volume Up key) with USB cable to your PC or Laptop. The Flashing procedure will start and Don’t disconnect the Yu Yureka Plus during flashing procedure. After finished this process, The command windows is automatically closed.

Step 6: Disconnect your device and remove memory card. Now boot your device by long pressing (approximately 3-5 minutes) the power button.

If this method is doesn’t work on your Yu Yureka Plus then you can use method 2.

Method 2: Follow steps to unbrick hard bricked Yu Yureka Plus by shorting:

Step 1: Following steps 1 to 4 of method 1.

step 2: Now open you device back cover and remove back panel screw one by one, then you will see main board like this. (see in this image)

Main board yu yureka plus

step 3: Now tap the point no. 2 and 6 by a wire. (for tap using a wire to short main board points, see in this image) Now Press and hold Volume Up key with tapping both points together, then connect your phone to PC via your USB cable.

Main board yu yureka plus 2

step 4: Now flashing procedure will start and Don’t disconnect the Yu Yureka Plus during flashing procedure. The command windows is automatically closed.

Step 5: Disconnect your device and remove memory card.Now boot your device by long pressing(approximately 3-5 minutes) the power button.

Must Read: Swap internal storage with the SD card in Android Lollipop and KitKat

I hope you like this unbrick hard bricked Yu Yureka Plus guide from which you will be able to easily unbrick hard bricked Yu Yureka Plus without any extra efforts. If feel any problem in this guide then please use comment box. Thanks to all.

11 response on “How to unbrick hard bricked Yu Yureka Plus

  1. rajesh

    my Yureka says waiting for device when shorting pin and get fastboot mode but it’s say waiting for device pls help it’s my second time hard brick. Any issue with Emmc image write problem or other…. Give me solutions…

    Reply
  2. Santosh

    should the tap or short be continued during all the flashing procedure? when should the shorted wire be removed

    Reply
  3. Richard

    Hi

    I just need to express my RELIEF. I followed your instruction point by point adn finally managed to bring back my dead Yu Yureka plus to life by using the wire bridge trick .

    Can not thank you enough !!!

    I am VERY VERY happy now.

    THANK YOU EVER SOOOOOOOOOOO MUCH

    regards Richard

    Reply
      1. ravi rai

        sir pls help my Yureka says waiting for device when shorting pin and get fastboot mode but it’s say waiting for device pls help

        Reply

Leave a Reply

Your email address will not be published. Required fields are marked *